New Innovative German Technology
(631) 293 8453

Installation Guide

installationTo cut and size Richter REVOslate all standard woodworking equipment can be used with carbide tooling. Table Saw; Router; Circular Saw; Laminate Trimmer; Miter Saw; Radial Arm Saw. For using panels with Richter REVOslate on both sides, it is recommended to score them because the stone surface on the backside tends to slightly splinter. Follow all equipment manufactures safety rules.

The actual substrate it is to be applied to is almost unlimited. All wood and lightweight materials are suitable. If the Richter REVOslate is only applied on one side of a carrier material, it is important to have a counter balance on the other side for stability. Mechanically mounted panels which have the Richter REVOslate on one side, need a craft paper or foil backing of at least 150 g / m2 (3.6128 pound/cubic inch). If applied as floor or wall panels, different climate conditions have to be taken into consideration.

For any substrate you use there are a few standard guidelines to follow:

  • The two products to be adhered together must be clean of dust, debris, grease and oils.
  • Use a suitable adhesive for your substrate.We recommend Mapei S997 1K adhesive.


installation_0203The Richter REVOslate adhesive requirements vary with the factory backing used on the veneer.

  • Polyester backed (standard backing) and Fleece backed (optional) can be adhered with our recommended Mapei S997 1K product. If alternative un-recommended adhesives are used, from experience, sometimes these products can react with the backing material and cause problems.

When using a hot or cold hydraulic panel press to bond the Stone-Veneer® to a substrate it is recommended you use a soft “buffer” sheet (such as a thin rubber sheet) on the Stone-Veneer® because of the natural 3-Dimensional surface variances.

Care, Handling and Cleaning Guidelines for Richter REVOslate

Care and Handling

Richter REVOslate is a real and natural slate product and it is as porous as any natural slate would be. The slate may absorb the oils found on your hands and fingers. Follow the cleaning instructions to remove any smudges. Wearing gloves when handling these materials will minimize the amount of cleaning required.


installation_04Any impurities splashed or spilled on the Richter REVOslate should be removed as soon as possible. In doing so warm water and a lightly moistened lint free cloth often suffices.

If the impurity or stain is not easily removed we recommend washing the surface with a soft lint free cloth moistened with a mild dish washing liquid and warm water solution. Alternatively, Mapei Cleaner L should be used and it is advised that a test area is done first.

If you do use any additional cleaners, test them on an inconspicuous area first to make sure they will not adversely harm or stain the surface of the Richter REVOslate.

If the Richter REVOSlate is being used in any wet areas such as kitchen backsplashes, near a food preparation area or sink it does need to be sealed. Bacteria and everyday stains and dirt can accumulate in the slate’s pores making it difficult to clean. The natural minerals present in your water can also accumulate in the stone’s pores. This is most noticeable in bathroom applications and shower/bath areas.

There are a variety of stone sealers on the market today and when applied according to the manufacturer’s recommendations will seal the pores on the Richter REVOslate surfaces. We have tested Tec™ EnsealantSB with very satisfactory results. It is a solvent based Stone Enhancer and Sealer.

Touch Up

Real slate will scratch when dragged across another piece of slate or a hard object. Many times what you see is the residual stone dust from the scratch. Cleaning as stated above will remove the stone remnants. If it is a much deeper scratch wiping a small trace of vegetable oil with your finger tip into the scratch will help prior to a light cleaning as above.

Please note that Richter REVOslate is a real slate stone. There are natural inconsistencies, fractures, color and surface variations and imperfections visible on the surfaces. These are quite normal and do not constitute faults or imperfections.